Open Source Robotics

A curated collection of high-quality open source robotics projects, tools, and software to propel the robotics community forward.

Thermoplastic Polyurethane

  • Also called: TPU
  • Category: Mechanical structure › Robot morphologies
  • Tags: materials, 3d-printing, soft-robotics, compliant-mechanisms, elastomers

A flexible, tough and elastic thermoplastic that can be 3D printed, molded or used as film; widely used in robotics for soft actuators, compliant fingers, grip pads, bellows and protective parts.

Definition

Thermoplastic polyurethane (TPU) is an elastic polymer that can be melted and reshaped, unlike cast silicones and thermoset polyurethanes. It is a block copolymer: hard segments, formed from a diisocyanate and a short chain extender, cluster into stiff domains that act as physical crosslinks, while long soft segments from a polyol give the material its rubber-like stretch. The ratio of hard to soft segments sets the hardness, which is usually given on the Shore A scale. TPU is a member of the wider family of thermoplastic elastomers (TPE), but not every TPE is a TPU.

TPU combines high elongation at break, good abrasion and tear resistance, and resistance to oils, which is why it is used in cable jackets, phone cases and shoe soles as well as robots. For desktop fused filament fabrication, filaments are commonly around Shore 85A to 98A in approximate terms, with 95A a frequent general-purpose grade. Softer grades are more flexible but harder to feed reliably: a direct-drive extruder with a constrained filament path, slow print speeds and dry filament help, because TPU absorbs moisture and prints with stringing and bubbles when wet. TPU powders are also used in selective laser sintering and similar powder-bed processes, and TPU-coated fabrics and films can be heat sealed into inflatable structures.

For robotics, the attraction is that one printed part can be stiff in one direction and compliant in another simply through its geometry and wall thickness. TPU is used for compliant fingers that wrap around objects, gripper pads, bellows and pneumatic actuators, flexure joints, bumpers, wheels and tires, and the flexible skins and leaves of bio-inspired robots. The material is viscoelastic, so it creeps under constant load and shows hysteresis under cyclic loading, and printed parts are anisotropic, with weaker bonding between layers than within them. Airtight printed actuators need tuned print settings and testing, since small gaps between extrusion lines can leak.

Why it matters

TPU is often the most accessible way to give a robot compliant, durable parts without molding, since it runs on common desktop printers. It makes soft and compliant designs quick to iterate, but designers need to account for its creep, hysteresis and anisotropy when the part carries load or must seal air.

Key applications

  • Printed soft pneumatic actuators and bellows
  • Compliant gripper fingers and grip pads
  • Flexure hinges and compliant mechanisms
  • Bumpers, wheels, tires and protective covers
  • Flexible skins and bodies for bio-inspired and soft robots
  • Heat-sealed inflatable structures from TPU-coated fabric

In practice

A team designs a soft gripper finger as a bellows-shaped pneumatic actuator printed in one piece from Shore 95A-class TPU. They dry the filament before printing, use a direct-drive extruder at low speed, and increase extrusion slightly so that the walls are airtight. Each printed finger is pressure-tested underwater to find leaks before assembly. During testing they notice that bending at a given pressure drifts over hundreds of cycles, so they characterize the finger after a break-in period and close the loop on bending using a flex sensor rather than relying on a fixed pressure map.

Common misconceptions

  • TPU and TPE are interchangeable terms — TPU is one chemical family within the broader class of thermoplastic elastomers, which also includes styrenic and olefinic types with different properties
  • Printed TPU parts are airtight by default — gaps between extrusion lines and layers can leak, so pneumatic parts need tuned settings and testing
  • A softer grade is always better for soft robots — softer grades are harder to print reliably and may lack the stiffness to hold shape or recover quickly

Who should know this

  • Soft robotics and gripper designers
  • Makers and hobbyists printing compliant parts
  • Mechanical engineers designing flexures and bumpers
  • Researchers building bio-inspired robot bodies

Related technologies

  • Fused Filament Fabrication
  • Selective Laser Sintering
  • Silicone Elastomer Casting
  • Compliant Mechanisms
  • Pneumatic Soft Actuators

Related terms

  • Soft Robotics
  • Gripper
  • Passive Compliance
  • Underactuated Hand
  • Vine Robot
  • Finite Element Method

Related projects

  • text-to-cad: Lets AI coding agents design parts in Python CAD and export robots to MuJoCo
  • SolidCraft: Open-source parametric 3D CAD in Rust that exports robot assemblies to URDF
  • SO-101 Open Robot Arm: 6-DOF robot arm for teleoperation and AI robotics research
  • BCN3D Moveo: Open-source 3D printed 5-axis robotic arm for education
  • Berkeley Humanoid Lite: Open-source sub-$5K humanoid robot with 3D-printed gearboxes and full sim-to-real pipeline
  • Thor: Open-source 3D-printable 6-DOF robot arm with stepper motors and GT2 belt drives

Videos

  • TPU is Underrated. Here's What You're Missing Out On.: JanTec Engineering

This website requires JavaScript to function properly. Please enable JavaScript to explore our collection of open source robotics projects.