Open Source Robotics

A curated collection of high-quality open source robotics projects, tools, and software to propel the robotics community forward.

Vine Robot

  • Also called: everting robot, eversion robot, growing robot, soft growing robot, tip-everting robot
  • Category: Mechanical structure › Robot morphologies
  • Tags: soft-robotics, eversion, pneumatic, growing-robots, inspection, search-and-rescue

A soft growing robot that extends from its tip by everting a thin pressurized tube, letting it lengthen through confined or cluttered spaces without sliding against its surroundings.

Definition

Vine robots are soft robots that move by growing. The body is a thin-walled, flexible tube, typically made of plastic film or coated fabric, that is folded inside itself and stored at the base, often on a spool. When the tube is pressurized with air, material passes through the center of the body and turns inside out at the tip, a process called tip eversion. The tip extends forward while the rest of the body stays still relative to the environment, much as a plant grows from its tip. The concept was presented by Elliot Hawkes, Laura Blumenschein, Joseph Greer and Allison Okamura in Science Robotics in 2017.

Because the body does not slide along its surroundings, a vine robot experiences little friction from the environment as it grows. It can lengthen through narrow gaps, deform to pass openings smaller than its own diameter, and move over sticky or rough surfaces that would trap a robot that drags its body. Length is limited mainly by how much material is stored at the base and by the pressure needed to evert it. Since the body is soft and light, contact with obstacles and people involves low forces.

Steering is one of the main design problems. Options include preformed bends or latches that release at set points along the body, artificial muscles or pouch actuators that shorten one side of the tube, tendons, and passive steering by letting the robot deflect off obstacles. Carrying a camera or sensor is difficult because the tip is made of constantly renewing material, so designs use tip mounts or caps that ride along with the everting front. Retraction is also hard: pulling the material back can make the body buckle instead of inverting cleanly.

Vine robots belong to the wider field of soft robotics and are also called everting or growing robots. Variations use different materials, multiple pressure chambers, or treat the everted tube itself as a deployable structure that can wrap around objects or be laid along a surface.

Why it matters

Vine robots can reach places that are hard for rigid or wheeled robots, such as rubble, pipes, ducts and narrow passages, because they extend without dragging their body along the walls. Their low cost, light weight and soft contact also make them candidates for working close to people and for medical and inspection devices.

Key applications

  • Search and rescue — reaching into rubble and confined voids
  • Pipe and duct inspection — growing through narrow, winding passages
  • Medical devices — catheter-like and endoscopic tools that advance without sliding against tissue
  • Exploration — investigating tunnels, caves and other narrow cavities
  • Deployable structures — forming supports, antennas or wrapping grippers on demand

In practice

A team building a vine robot usually starts with a tube of low-density polyethylene film or thermoplastic-coated ripstop fabric, heat-sealed or bonded to the target diameter, and mounts it on a spool inside a pressurized base with a motor that controls how fast material is released. Pressure is set high enough to evert the tube but low enough to keep contact forces small. They add steering actuators along the body, or preformed bends for a known route, and fit a camera on a tip cap if visual feedback is needed. Testing focuses on growth through representative obstacles, on how the robot behaves when it buckles, and on whether it can be retracted without tangling.

Common misconceptions

  • Vine robots crawl like snakes — they extend by everting material at the tip, while the body stays in place relative to the environment
  • Soft means they cannot exert force — internal pressure lets the tip push, lift and support loads, though forces are limited by pressure and diameter
  • They can grow indefinitely — length is limited by stored material, the pressure needed to evert it, and friction inside the body
  • Retraction is simply growth in reverse — pulling material back often causes buckling and needs dedicated mechanisms

Who should know this

  • Soft robotics researchers
  • Search and rescue and inspection engineers
  • Medical device designers
  • Students and makers interested in low-cost robot designs

Related technologies

  • Soft Robotics
  • Pneumatic Artificial Muscles
  • Continuum Robots
  • Snake Robots
  • Inflatable Structures
  • Tendon-Driven Actuation

Related terms

  • Soft Robotics
  • Manipulator

Related projects

  • OpenDroneMap: Open-source photogrammetry toolkit that turns drone images into maps and 3D models
  • SOFA Framework: Real-time physics simulation framework for medical simulation and soft tissue modeling
  • Delta X Soft Gripper: Soft gripper for the Delta X robot: STL and STEP files, print settings and a build video

Videos

  • Stanford researchers develop vine-like, growing robot: Stanford

This website requires JavaScript to function properly. Please enable JavaScript to explore our collection of open source robotics projects.