Stringman
Cable-suspended household crane robot driven by four corner-mounted lines
License
- software: Apache 2.0
- hardware: CERN-OHL-W 2.0 (weakly reciprocal)
- pcb: no licence (all rights reserved)
- documentation: CC BY-SA 4.0
Split licensing. The firmware (nhnifong/cranebot3-firmware) is Apache-2.0. The hardware designs - CAD document, STL files, Print Guide and BOM - are CERN-OHL-W 2.0 with an addendum stating that the user assumes full responsibility for any injury, damage or loss resulting from installation or use. The PCB repository (nhnifong/stringman-pcbs) carries no licence file, so the KiCad projects and Gerbers are published without an open-source grant - all rights reserved by default. Checked 2026-08-07.
Overview
Stringman is a cable-driven household robot from Neufangled Robotics. Instead of standing on the floor, it hangs from the room itself: two 3D-printed anchors screw into the studs of opposing corners, each spooling two lines that run out through eyelets in the other two corners. Reeling those four lines in and out flies a gripper anywhere inside the volume they enclose, so the robot's working area is the room rather than the reach of an arm. A 27 cm pole below the gripper carries a marker whose AprilTags let the anchor cameras localise the payload, and active swing cancellation damps the pendulum motion that cable robots are prone to.
Each anchor runs a Raspberry Pi 3A+ and the gripper a Raspberry Pi Zero 2W, on the household wifi. Kits bought before 8 August 2026 have an older 50 cm ABS pole. A separate motion controller (stringman-headless) on a host machine discovers them over mDNS, solves the kinematics and streams telemetry as protobuf over a local websocket on port 4245. That socket is the only interface the web UI uses, so any program can drive the robot the same way, and a LeRobot bridge records teleoperation episodes and replays trained policies through the same contract. The cloud relay at neufangled.com is optional; in LAN mode no video leaves the network.
The build splits into three printed assemblies and one room installation. Each anchor holds two Damiao DM-H6215 hub motors driving glued two-part spools - three carry 50 lb braided fishing line, the fourth carries the power cable through a 22 mm slip ring so the gripper can be fed 24 V down a line that also winds. The anchor frame prints in PCTG or PETG-CF rather than PLA because it carries the load, and a Camera Module 3 sits in an adjustable tilt adapter (earlier anchors used fixed 22, 26 or 30 degree adapters). The gripper carries a wide-angle camera, a VL53L1 laser rangefinder, a force-sensing resistor behind the grip tape, two STS3215 smart servos - one for the geared finger levers, one for the helical wrist gear - and a 30 mm fan.
Upstream publishes a per-component print and build time: 40 hours of printing and 1.5 hours of assembly per anchor, 20 hours and 2 hours for the gripper, and about 80 hours for the plate as a whole. Installation is quoted at an hour plus at least 30 minutes of setup, and is compared to hanging a curtain rod - anchors must land in wooden studs, because the loads are lateral and adhesive mounts are explicitly ruled out. Spool winding is not done by hand: a self-test script on each Pi (qa-anchor-arp, qa-gripper-arp) sets the motor IDs, winds the correct length for each spool type and checks the camera. Calibration then locates the anchors and eyelets from four printed AprilTag cards laid on the floor.
Why it matters
Household manipulation is usually attempted with an arm, which trades workspace for rigidity - a desktop arm can reach a table, a mobile manipulator large enough to reach a room costs more than a car. Stringman inverts the trade: the structure is the room, and four lines carry up to 2 kg across a whole bedroom for about $636 in parts. That makes it one of the few open designs where a hobbyist can collect real household manipulation data at room scale, and the LeRobot dataset bridge means the episodes go straight into the same training pipeline the rest of the field uses.
Problem it solves
Reaching anywhere in a room without a robot large enough to fill it. A cable robot gets its workspace from where the anchors are mounted rather than from link lengths, so the hard parts move from mechanics to sensing and control: knowing where the payload is, and stopping it swinging. Stringman solves the first with AprilTags on a marker watched by two anchor cameras, and the second with active swing cancellation in the motion controller.
Key takeaways
- Two wall anchors and four lines turn an entire room into the robot's workspace, for a published parts cost of $635.60 (anchors $450.54, gripper $185.07)
- A slip-ring powerline spool feeds 24 V down one of the four lines, so the gripper needs no battery and no trailing cable
- Every printed part, the full BOM with supplier links, and per-subassembly build guides are published - the hardware is CERN-OHL-W 2.0, the firmware Apache-2.0
- The control interface is a documented protobuf websocket on port 4245, so a policy or script drives the robot through exactly the same contract as the web UI
- LeRobot integration records teleoperation episodes to a Hugging Face dataset and runs trained DiT policies back through the same socket
- Upstream publishes the envelope rather than leaving it to guesswork: up to 2 kg payload, ~0.4 m/s traverse, rooms 2-7 m across, and ~800 hours of testing in real homes
Who it is for
- Makers with a 3D printer who want a room-scale robot without a room-scale budget
- Imitation-learning researchers who need household manipulation episodes in LeRobot format
- Cable-robot and mechatronics builders studying line-driven kinematics and swing damping
Limitations
- Obstacle avoidance is not implemented - the install guide warns you may have to intervene manually when furniture is inside the work area
- Self-parking depends heavily on calibration quality and upstream recommends parking by hand for now
- Mounting needs wooden studs behind the wall or structural columns to strap to; adhesive mounts and drop-ceiling T-bars are ruled out, so some rooms need a backer board
- The motion controller needs a host machine with at least 8 cores, 8 GB RAM and a PyTorch accelerator - it does not run on the Raspberry Pis
- The PCB repository (nhnifong/stringman-pcbs) carries no licence file, so the KiCad projects and Gerbers are published but not formally open
- CAD is published as Onshape documents only - the printable STLs and 3MFs are downloadable, but there is no neutral STEP export for editing offline
- The published work envelope is a room 2-7 m across the XY diagonal with a length-to-height ratio between 0.9 and 2.5 - long, narrow or very tall rooms fall outside it