Open Source Robotics

A curated collection of high-quality open source robotics projects, tools, and software to propel the robotics community forward.

Assembly guide for SSG48 Adaptive Electric Gripper

Open-source 3D-printed electric gripper that sets its grip force on every move

License

  • hardware (SSG-48 repository: STL and STEP files, BOM, assembly manual, cable guide): CERN-OHL-S 2.0 (strongly reciprocal)
  • manual (SSG48-gripper-docs: text and images): CC BY-SA 4.0
  • driver firmware (Spectral Micro BLDC controller): GPL 3.0
  • software (Spectral-BLDC Python library; MSG gripper ROS 2 driver): MIT
  • robot models (Source-Robotics/robot_descriptions: URDF and MuJoCo): CC BY 4.0

Hardware: the SSG-48 repository (STL and STEP files, BOM, assembly manual, cable guide) is under CERN-OHL-S-2.0 since 4 Nov 2026, read from its LICENSE file; until then it was Apache-2.0. CERN-OHL-S-2.0 is strongly reciprocal: you may build, sell and change the gripper, but if you share or sell a modified design or hardware made from it, you must publish your design sources under the same licence. Manual: the SSG-48 manual's text and images are CC BY-SA 4.0 and its code examples MIT. Firmware: the Spectral Micro driver firmware the gripper runs is GPL-3.0. Software: the Spectral-BLDC Python library and the MSG gripper ROS 2 driver are MIT. Robot models: the URDF and MuJoCo models in robot_descriptions are CC BY 4.0, so credit Source Robotics and say what you changed. Community ROS 2 packages: Lass6230/ssg48_adaptive_electric_gripper_ros2 and LionelBirglen/SSG48_PacomeFlex_ROS2_Public have no licence file, so they are not licensed for reuse. Card image: a frame of Source Robotics' own video, not covered by the hardware licence. Checked 2026-11-12 against each repository's LICENSE file and the manual.

Assembly guide

1. Before You Start

The SSG-48 assembly manual (version 1.1) shows each step in drawings, and the build guide in the SSG-48 manual adds the driver setup and the thermistor. Page numbers refer to the assembly manual.

1.1 Read the manual and the warnings

Manual pages 2 to 5.

  1. Read the whole manual before building: the gripper can burn, electrocute and hurt you.
  2. Upstream says the gripper is for development, demonstration and evaluation, and is not CE, UL, FCC or RoHS compliant.
  3. Follow the assembly video alongside the manual.

1.2 Print the parts

Manual page 6 and the build guide's printing page.

  1. Print the V2 set (the large-bearing body, lid, gear and magnet shaft), 2 jaws, the guide cover and the coupler connector for your robot in PETG.
  2. Upstream's reference prints were made on a Prusa MK2S in PETG with 25% infill, with supports only where a part needs them.
  3. Clean all support material off, especially from the bearing seats and the rail slot.
  4. Print fin-ray fingers in a flexible filament.

1.3 Collect tools and consumables

Manual pages 7 and 8.

  1. Tools: screwdriver set, drill, soldering iron, hex key set, torque screwdriver, rubber hammer, hammer and pliers.
  2. Consumables: blue threadlocker, lithium grease, solder, heat shrink tube and thermal cement.
  3. Use an electric screwdriver if you like, but do the last turns by hand or with the torque screwdriver, or you risk destroying the threads.

2. Jaws and Motor

Manual pages 10 to 15.

2.1 Build the 2 jaws

Parts: 2 jaws, 2 MGN7C carriages, 8 M3 brass inserts 5 mm long. Fasteners: 8 × M2 4 mm.

  1. Press the brass inserts into each jaw with a soldering iron.
  2. Place an MGN7C carriage in its seat in the jaw and fix it with 4 × M2 4 mm screws; use threadlocker if needed.
  3. Build the second jaw the same way.

2.2 Fit the gear and magnet to the motor

Parts: gripper gear, magnet shaft, GBM5208-75 motor, magnet. Fasteners: 4 × M3 5 mm cheese head, 1 × M2 10 mm.

  1. Fix the gripper gear to the motor with the 4 M3 5 mm screws.
  2. Fix the magnet shaft to the gear with the M2 10 mm screw.
  3. Push the magnet onto the shaft; if it is loose, secure it with super glue.

2.3 Mount the motor in the body

Parts: main body, 3 M3 brass inserts 5 mm long, 1 M3 brass insert 3 mm long. Fasteners: 2 × M3 8 mm cheese head, 1 × M3 5 mm cheese head.

  1. Fit the brass inserts into the body where the manual's arrows show.
  2. Slide the motor assembly into the body, with the motor wires on the side the manual marks.
  3. Fix the motor with the screws, and leave the hole marked with a red cross empty: the thermistor goes there later.

3. Electronics

Manual pages 16 to 21, and the build guide's notes on the thermistor.

3.1 Wire the M8 connector

Parts: M8 4-pin connector and its nut, 4 M3 brass inserts 5 mm long, 4 wires of 100 mm.

  1. Fit the brass inserts and put the connector's nut in its slot.
  2. Solder the 4 wires to the connector, with 2 as a twisted pair for the CAN bus, and cover the soldered connections with heat shrink.
  3. Use the manual's pinout: 1 is 24 V, 2 is CANL, 3 is GND, 4 is CANH.
  4. Pull the wires through the hole and the nut, then screw the connector in.

3.2 Connect the driver

Parts: Spectral Micro driver, 100K NTC thermistor, 3 wires of 20 mm. Fasteners: 4 × M3 8 mm cheese head.

  1. Route the wires through the hole the manual marks in red and out through the green one, then solder or crimp the driver's CAN and power connectors, minding the polarity.
  2. Solder the thermistor to the driver's TERM and 3V3 pads, with leads about 35 mm long.
  3. Solder the 3 wires of 20 mm to the motor contacts.
  4. Fix the driver in the body with the 4 M3 8 mm screws, in the orientation the manual shows, and plug in the power and CAN connectors.

3.3 Fit the thermistor

Without it the gripper has no temperature protection and can burn out its motor.

  1. Lead the thermistor into the motor windings through the hole left free earlier.
  2. Fix the bead with thermal cement and let it set: thermal paste stays soft and lets it move, and ordinary glue insulates it.
  3. Keep the leads clear of the rotor.

4. Driver Setup

Calibrate the motor before the linear guide goes on, because the racks would block the calibration's turns. Manual pages 22 and 23, and the build guide's driver setup page.

4.1 Connect to the driver

A gripper from the shop arrives configured; a self-built one starts with a bare driver.

  1. Connect a 3.3 V USB-to-serial adapter to the driver's UART connector and open a terminal at 256000 baud with CR+LF line endings, or use Motor GUI over UART.
  2. Power the driver with 24 V.

4.2 Calibrate the motor

The driver measures the motor and finds its pole pairs by itself.

  1. Send #Default, then #Cal, and wait for Calibration success!
  2. If it stops with an error, check the motor's 3 wires and the encoder magnet.
  3. Default also resets the driver's serial number: note what #SERNUM prints first if you need it.

4.3 Turn on gripper mode and save

Nothing survives a power cycle until it is saved.

  1. Send #Gripper 1, #Term 1, #Tlim 75 and #CANID 0, then #Save.
  2. Motor GUI's SSG-48 preset writes the same settings and the current gains, but sets CAN ID 6 for the PAR6: change it for another robot.
  3. After a power cycle, #Temp should print the room temperature; a temperature error means the thermistor is not connected.

5. Rail, Lid and Coupler

Manual pages 24 to 32.

5.1 Fit the linear guide

Parts: MGN7 linear guide, guide cover. Fasteners: 4 × M2.5 8 mm.

  1. Slide both jaws onto the linear guide and the guide cover, and grease the jaws with lithium grease.
  2. Close the jaws and check that both sit at the same distance from each end.
  3. Fit the guide to the body so the jaws have the same travel on both sides, and fix it with the 4 M2.5 8 mm screws.

5.2 Close the body

Parts: main body lid. Fasteners: 4 × M3 12 mm, and 3 × M2 10 mm if needed.

  1. Fix the lid with the 4 M3 12 mm screws.
  2. If the 2 shells leave a large gap, usually from print quality, add 3 M2 10 mm screws where the manual marks.

5.3 Fit the coupler connector

Parts: shaft coupler, coupler connector. Fasteners: 4 × M4 20 mm, 4 × M3 10 mm.

  1. Fix the shaft coupler to the coupler connector with 4 M4 20 mm screws, minding the orientation of its side holes.
  2. Use the PAROL6 or PAR6 coupler connector for those robots, or adapt the generic one to yours.
  3. For PAROL6, put an M3 12 mm screw in the marked hole: the robot homes against it.
  4. Fix the coupler connector to the gripper with 4 M3 10 mm screws.

6. Cable and First Run

Manual pages 33 to 35, the cable guide and the manual's page on PAROL6 and PAR6.

6.1 Make or buy the cable

The cable is not in the box with a bought gripper either.

  1. Buy the PAROL6 gripper cable from Source Robotics, or make one from 0.4 m of 4-wire twisted-pair cable and M8 4-pin male and female connectors.
  2. PAROL6 and PAR6 put the signals on different pins: a cable for the wrong robot puts 24 V on the CAN bus and destroys the driver. Check the pinout before the first plug-in.
  3. For PAROL6, the homing tab must be on the same side as the cable connector.

6.2 Calibrate and move the gripper

The gripper calibration finds both end stops; it runs after every power-up.

  1. Power the gripper through its cable and run the gripper calibration (#Gripcal, or Calibrate in Motor GUI): the jaws open fully and close fully.
  2. Make a first move at a low current.
  3. Calibrate again after changing the fingers.

6.3 Mount it on PAROL6

The robot's software then calibrates and drives the gripper.

  1. Slide the gripper onto the joint 6 shaft and tighten the 2 screws of the shaft coupler with blue threadlocker.
  2. Keep the node ID at 0 and switch the gripper's CAN termination on: it is the last node on the robot's bus.
  3. Set j5_homing_offset to 8035 in main.cpp of the control board firmware, as the PAROL6 documentation describes for the SSG-48.

This website requires JavaScript to function properly. Please enable JavaScript to explore our collection of open source robotics projects.