Assembly guide for Open-source Leader Arm
Servo-free 3D-printed leader arm that teleoperates an SO-ARM for about 27 USD
License
Apache-2.0
Assembly guide
1. Print and wire up
Print the parts, then wire the six encoders before any of them is buried in the arm.
1.1 Print the 19 parts
PLA, 0.2 mm layer height, 15% infill. All parts are supplied pre-oriented and print without supports.
- Print all 19 unique parts, 49 pieces in total, from cad_files/stl.
- If a part loads at an odd angle in the slicer, lay its flat face on the bed.
- For bearing_housing, add a pause at 10 mm height (layer 50 at 0.2 mm), drop in the 608 bearing seated flat, then resume.
1.2 Wire the six encoders
Do this first: once the arm is together there is no room to solder.
- Wire all six AS5600 encoders to the TCA9548A and the ESP32 as shown in docs/wiring.png.
- Multiplexer to ESP32: VIN to 3V3, GND to GND, SDA to D18, SCL to D19, RST to 3V3, and A0/A1/A2 to GND.
- Each encoder takes VCC from 3V3, GND and DIR to GND, and its SDA/SCL to the SDn/SCn pair of its own channel.
1.3 Fit the magnets
Each rotor carries the magnet the encoder underneath it reads.
- Press the 5 mm diametric magnet into the circular pocket in each of the six rotors.
2. Joint 0 and the base
Build the first joint, give it its encoder, and stand the arm up on its base.
2.1 Assemble joint 0
The perpendicular-link pattern used by joints 0, 3 and 4.
- Stack rotor, bearing_housing, link_perpendicular_base, link_perpendicular_body and washer_perpendicular_link — this is joint_0.
- Attach the base_connector to that assembly.
2.2 Fit the joint 0 encoder
Joints 0 and 5 get their encoders now; the middle four are left until the end to keep the wiring clear.
- Add the encoder_housing with its AS5600 encoder to the assembly.
- Tie a knot in the encoder wire, then fit the encoder_housing_cap so a pull on the wire acts on the cap and not on the encoder.
2.3 Mount the base
Gives the arm somewhere to stand and somewhere to rest.
- Attach the base.
- Add the rest_pose_holder_base and rest_pose_holder_body, which hold the arm in its reference pose.
3. Shoulder, elbow and wrist
Joints 1 to 4, alternating a bearing housing with the next link.
3.1 Joint 1: shoulder
Round-washer pattern, used again for joints 2 and 5.
- Attach a bearing_housing to the previous assembly.
- Add rotor, link_shoulder_to_elbow and washer_round — this is joint_1.
3.2 Joint 2: elbow
Same two moves, one link further out.
- Attach a bearing_housing to link_shoulder_to_elbow.
- Add rotor, link_elbow_to_wrist and washer_round — this is joint_2.
3.3 Joint 3: wrist roll
Back to the perpendicular-link pattern from joint 0.
- Attach a bearing_housing to link_elbow_to_wrist.
- Add rotor, link_perpendicular_base, link_perpendicular_body and washer_perpendicular_link — this is joint_3.
3.4 Joint 4: wrist pitch
The last of the perpendicular joints.
- Attach a bearing_housing to the joint 3 assembly.
- Add rotor, link_perpendicular_base, link_perpendicular_body and washer_perpendicular_link — this is joint_4.
4. Tooltip and handle
The joint the operator actually holds.
4.1 Joint 5: tooltip
The last joint, and the second one to get its encoder now rather than later.
- Attach a bearing_housing to the joint 4 assembly.
- Add rotor, link_tooltip and washer_round — this is joint_5.
- Add the encoder_housing with its AS5600 encoder, then tie a knot in the wire as before.
4.2 Fit the handle
The handle_base doubles as the cap for the joint 5 encoder.
- Attach the handle_base, which also closes the encoder housing on this joint.
- Attach the handle_body.
5. Cabling and counterbalance
Tidy the encoder runs and take the weight off the operator's hand.
5.1 Route the wires
Three printed clips keep the encoder runs off the joints.
- Clip the three wire_holders onto link_shoulder_to_elbow and link_elbow_to_wrist and run the encoder wires through them.
5.2 Fit the counterbalance
One rubber band between the two links carries the arm's weight.
- Route a single rubber band through both rubberband_housings.
- Fix one housing to link_shoulder_to_elbow and the other to link_elbow_to_wrist.
6. Finish and bring up
Add the four remaining encoders, then check the arm from the serial monitor.
6.1 Fit the four remaining encoders
Joints 1 to 4, in the same way as the two already done.
- For each of the four remaining joints, add the encoder_housing with its AS5600, tie a knot in the wire and fit the encoder_housing_cap.
6.2 Flash and check
The firmware tells you whether each joint is wired and magnetised correctly.
- Install ESP32 board support in the Arduino IDE, open firmware/firmware.ino, select the board and port, and upload.
- Open the serial monitor at 115200 baud: each channel should report the encoder found and 'magnet ok'; a -1 means a wiring or magnet problem on that channel.
- After the scan the board streams six comma-separated angles at 100 Hz.
6.3 Drive the simulated follower
Nothing here needs a physical follower arm.
- Install the host dependencies: pip install "mujoco>=3.2" pyserial, and clone google-deepmind/mujoco_menagerie into the working directory.
- Run python teleop.py --port <your ESP32 port>, or teleop_sort_task.py for the block-sorting scene.
- Hold the leader arm in its reference pose and press ENTER when prompted, so leader and follower start aligned.