Open Source Robotics

A curated collection of high-quality open source robotics projects, tools, and software to propel the robotics community forward.

Backlash

  • Also called: Gear Backlash, Lost Motion, Free Play
  • Category: Actuation & drivetrain › Ratings
  • Tags: gears, transmission, accuracy, backlash, metrology

The free play in a transmission — how far the output moves before the input picks it up again after a reversal, usually quoted in arcminutes.

Definition

Backlash is the lost motion between the input and output of a transmission: the amount you can move the output back and forth without the input moving at all. It exists because meshing gear teeth need clearance to run without binding, and because bearings, splines and couplings each contribute their own slack. It is quoted as an angle at the output, usually in arcminutes — one arcminute being a sixtieth of a degree.

Backlash matters because it breaks the assumption most control code makes, namely that commanded joint position equals actual joint position. On a direction reversal the output stands still for the width of the backlash and then catches up, which shows up as position error on every change of direction, as a limit on how hard a position loop can be tuned before it hunts, and as visible chatter in machining or drawing tasks. It also compounds along a kinematic chain: a small angular slack at the shoulder becomes a large positional error at the end effector, multiplied by the reach.

Backlash should not be confused with compliance. Compliance is elastic — the joint deflects under load and springs back, and it is repeatable and can be modelled or compensated. Backlash is a dead zone in which the output is simply not controlled, and it is not reliably repeatable. This distinction drives transmission choice: strain-wave gears are near-zero backlash but noticeably compliant under torque, planetary gearboxes are stiff but carry backlash of several arcminutes unless preloaded, and cycloidal drives sit between the two.

Why it matters

Backlash is usually the first hard limit a builder meets on accuracy, and it is invisible in a parts list. A robot arm assembled from good motors and encoders can still wander by millimetres at the tip because a few arcminutes of slack at each joint accumulate along the chain. Because encoders are normally mounted on the motor rather than the output, the control loop cannot even see the error — the joint reports that it is exactly where it was told to be. Understanding backlash is what turns a datasheet number into a prediction about how a machine will actually behave.

Key applications

  • Comparing gearbox datasheets, where backlash is quoted in arcminutes
  • Diagnosing position error that only appears on direction reversals
  • Deciding whether an encoder belongs on the motor or on the joint output
  • Specifying joints for machining, drawing, dispensing or inspection tasks
  • Budgeting end-effector accuracy across a multi-joint kinematic chain

In practice

You measure it by locking the input and rocking the output against a dial indicator at a known radius, then converting the deflection to an angle. Typical figures: strain-wave gears under one arcminute, quality cycloidal drives around one, precision planetary gearboxes three to five, and standard planetary or printed gear trains ten or more. Common mitigations are preloading or split gears, mounting the encoder on the output rather than the motor so the loop can see the true position, and approaching every target from the same direction so the slack is always taken up the same way — the trick CNC machinists have used for decades.

Common misconceptions

  • Backlash and compliance are the same thing — compliance is elastic and repeatable, backlash is an uncontrolled dead zone
  • A motor-side encoder will detect it — it sits after the encoder, so the controller reports the joint as being on target
  • Zero backlash is always the goal — eliminating it costs money, efficiency and shock tolerance, and a legged robot may care far more about impact survival
  • It is constant — backlash varies with position, temperature, preload and wear, which is exactly why it is hard to compensate in software

Who should know this

  • Anyone building an arm that must be accurate rather than merely strong
  • Builders whose repeatability is good in one direction and poor in the other
  • Anyone choosing between planetary, cycloidal and harmonic transmissions
  • Engineers deciding where to place encoders in a joint
  • Students learning why industrial arms cost what they do

Related terms

  • Cycloidal Drive
  • Harmonic Drive
  • Planetary Gearbox
  • Encoder
  • Direct Drive

Videos

  • How to measure Gear Backlash and Center Distance: Evolvent Design
  • What Are Gear Backlash and Backdrive in Mechanical Design?: Bonsystems Global

Wikipedia

  • Backlash (engineering)

This website requires JavaScript to function properly. Please enable JavaScript to explore our collection of open source robotics projects.